OfficeStyler T10
For Microsoft Windows 2000/XP

#### INTRODUCTION

This Readme file contains information about using OfficeStyler T10 Printer driver and Twain driver for Windows 2000/XP. Please make sure to read this before installing the OfficeStyler T10.

Note: Please note that this release of OfficeStylerT10 for Win2000/XP supports the Printer and Twain drivers only. The PC-Fax option is not supported with this version.

#### CONTENTS

OPERATIONAL ENVIRONMENT

[1]How to install OfficeStyler T10
(1)Installing OfficeStyler T10 at the first time
Using Setup Program
Using Plug and Play
Using Add Printer
(2)Uninstalling OfficeStyler T10
(3)Updating OfficeStyler T10
(4)Notes

[2]Limitation/Notes in using OfficeStyler T10 printer driver
(1)Limitation/Notes in using with each Operating System
(2)Limitation/Notes in printing

OPERATIONAL ENVIRONMENT
This operates on environment listed below:
[Hardware]
* PC/AT compatible model with Intel 486 or later.

[Operating System]
* Windows 2000 Professional / Windows 2000 Server
* Windows XP Professional / Windows XP Home Edition

Appropriate drivers are provided for each OS, please use the correct driver for your operating system.

#### [1]How to install OfficeStyler T10 Windows 2000/XP

(1)Installation steps of Windows 2000/XP drivers

There are three ways of installing the OfficeStyler T10.

- Using Setup program

- Plug and Play

- Add printer

When using Windows XP, the “Found New Hardware” dialog window appears even if the OfficeStyler T10 has been installed. To prevent display the “Found New Hardware” dialog window, please do the following steps.

1.Install the OfficeStyler T10 by using Setup program.

2.Uninstall the OfficeStyler T10.

3.Install the OfficeStyler T10 by using the Plug and Play procedure.

Using Setup program

Note: Keep the power of your printer off.

- 1 | Start Windows and log on as Administrators or Power Users.
- 2 | Run the setup.exe program to install OfficeStyler T10 Windows 2000/XP.
- 3 | Click "Next >" to continue Setup program on the "Welcome" windows. Click "Cancel" to terminate Setup program. Note: Check Environment The OfficeStyler T10 Windows 2000/XP will detect the current OS version and protect you from installing the driver under wrong OS platform. For examples, if you intend to install this driver upon Windows NT, it will pop-up the warning message dialog to confirm and to stop the setup. Note: Check Version If the setup finds a previous version of OfficeStyler T10, you will see the message dialog. If you want to uninstall the previous version, click "Yes" to uninstall the previous version of the OfficeStyler T10. Click "No" to terminate Setup program. After uninstall is completed, you will see the warning message dialog. Click "OK" to restart your PC. Go back to the step 1 to start setup again.
- 4 | Select Setup type, then click "Next >" to continue Setup program. If select "Multifunctional driver", both Printer driver and Twain driver will be installed. If select "Printer driver only", Description will display "Printer driver only" and only Printer driver will be installed.. |
- 5 | Select the installing folder for OfficeStyler T10. Click “Next >” to install to “C:\Program Files\OST10” holder. If you want to change the folder from the one displayed in the dialog, click "Browse..." and change to the folder name, then click "OK". |  |
- 6 | Select the port you want to use with installed printer. After selecting, click "Next >". |  |  |
- 7 | If you want to use installed printer as the default printer, click "Yes", then click "Next >". |
- 8 | Setup will copy files to destination paths. |
- 9 | Click "Finish", and finally, the installation is completed after restart your PC. Note: If you choose "No, I will restart my computer later.", there will be a message box to ask you to restart. |

After completing above operation, you can use OfficeStyler T10 for Windows2000/XP.

## Plug and Play

- 1 | Turn the power of printer on. Start Windows and log on as Administrators or Power Users.
- 2 | The Windows2000 or XP can automatically detect the connection for the printer as the Plug and Play device pop up a “Found New Hardware” dialog and begin to install.
- 3 | Follow the Windows instruction to install the OfficeStyler T10.
| Note:The settings of the Windows menu for the port setting and default printer setting are ignored.

Add Printer

- 1 | Start Windows and log on as Administrators or Power Users. Open "Add Printer" icon in the Printers folder. After opening, click "Next >".
- 2 | Select printer management control (My Computer or Network Printer Server / Local or Network Printer) following the guidance of Add Printer Wizard. After selecting, click "Next >".
- 3 | Select the port you want to use with installed printer. After selecting, click "Next >".
- 4 | Click "Have Disk..." button in "Manufacturers:" / "Printers:" window. After selecting, click "Next >".
- 5 | Click "Browse.." and change to the proper drive name, then click "OK".
- 6 | Select the OEMSETUP.INI. After selecting, click "Next >".
- 7 | Specify printer name. And even if you set the installed printer as the default printer, the setting is ignored. Click "Next >".
- 8 | Even if you set sharing installed printer with other network users, the setting is ignored. Click "Next >".
- 9 | Print test page to confirm that the printer is set up properly. Check on "Yes (recommended)", then click "Finish", and finally, the installation is completed.

After completing above operation, you can use OfficeStyler T10 for Windows2000/XP.

(2)Uninstalling OfficeStyler T10

Please follow the steps to uninstall the OfficeStyler T10 from your PC;

- 1 | Start Windows and select "Add/Remove Program" from the Control Panel.
- 2 | Select "OfficeStyler T10", and click "Change/Remove".
- 3 | When your PC confirms your selection, click "Yes". The program and all its components are removed from your PC.
- 4 | When uninstall is done, click "OK".
- 5 | You will see the dialog box shown below. Click "OK" to confirm, and restart your PC.

(3)Updating OfficeStyler T10
Please follow these installation steps to update the OfficeStyler T10 from old version to new version;

- 1 | Start Windows and select "Add/Remove Program" from the Control Panel, then remove the OfficeStyler T10 to select "OfficeStyler T10" item under the install/uninstall tab. Refer to the procedure about how to uninstall the OfficeStyler T10.
- 2 | Restart PC.
- 3 | Install new version of OfficeStyler T10 with the same step as "(1): Installing OfficeStyler T10 at the first time." See installation steps for each OS as follows; Installation steps of Windows2000/XP drivers

After completing above operation, you can use OfficeStyler T10 for Windows2000/XP of new version.

(4)Notes

* | During Add Printer and Plug and Play installation, you will see the Microsoft Certification on Digital Signature. OfficeStyler T10 will ignore the warning message if you want to continue perform the setup.
* | During Add Printer and Plug and Play installation, the settings of the Windows menu for the port setting and default printer setting are ignored.

####

#### [2] Limitation/Notes in using OfficeStyler T10 printer driver

(1)Limitation/Notes in using with each operating system

See OPERATIONAL ENVIRONMENT.

(2)Limitation/Notes in printing

* | Following functions are not available compared with the Windows95/98 printer driver.
| - | Manual double-sided print function
| - | Cover page print and Trailer page print function
| - | PCL4.5 Soft Emulation (It is not necessary for Windows2000 and XP)
| - | DOS Box (It is not necessary for Windows2000 and XP)
| - | Paper size selection of the "Government Letter" and "Government Legal"
| - | Overlay print function
| - | Print to File function
| - | Status Display function * Error indication is shown only in the Message Box. * "Ready", "Printing", "Warming up" messages are not shown. * Job status display (File name, # of page, GDI/PCL mode) is not shown. * Animation display is not shown * Print job control function (Pause/Resume/Delete) is deleted. (Windows print queue support these function) * Option setting is not available
| - | Print manager function
| - | Test print function
| - | On Line Help function
| - | Share printer function (Network printing is possible with Windows share print)
* | It’s impossible to delete a printer job from Windows printer spooler when using “Reverse Order Printing”. If you want to delete a “Reverse Order Printing” job, you have to create an error on your printer like a paper out condition, then let the message box pop up and then press the “Cancel” button to delete the printer job.

The product and company names described above are the trademarks or brand names belonging to each company.